7. Dezember Lichtsensor
Verfasst: 07.12.2018, 16:53
7 Lichtsensor
Hinter dem 7. Türchen findest du einen Fototransistor. Das Bauteil sieht aus wie eine LED in einem klaren Gehäuse.
Von vorn sieht man jedoch die dunkle, lichtempfindliche Fläche.
Der längere Anschluss ist der Emitter.
Der kürzere Anschluss heißt Kollektor.
Bei Dunkelheit ist der Fototransistor ein Isolator. Aber je mehr Licht auf seine empfindliche Fläche fällt, desto mehr Strom leitet er.
Die Spannung am Trigger-Eingang sinkt dann. Bei genügender Helligkeit schaltet der NE555 die LED ein.
Sie bleibt danach auch bei Dunkelheit an, bis sie mit dem Taster gelöscht wird.
Der Fototransistor arbeitet zusammen mit dem Widerstand von 22 kOhm als Spannungsteiler.
Bei Dunkelheit ist die Spannung hoch (9 V), mit steigender Helligkeit sinkt sie. Sobald die Spannung unter 3 V fällt,
schaltet der NE555 seinen Ausgang ein. Du kannst die beiden Widerstände in der Schaltung tauschen,
um die Empfindlichkeit zu ändern. Mit 10 kOhm im Spannungsteiler schaltet der Sensor erst bei größerer Helligkeit ein.
7 Light sensor
Behind the 7th door, there is a photodiode. It looks like a LED in a clear shell.
But at the front, you can see a dark, light-sensitive surface.
The longer port is called the emittor.
The shorter port is called the collector.
In darkness, the photodiode is an isolator. But it gets more conductive the more light falls onto its photosensitive surface.
If that happens, the voltage at the Trigger-entry drops. If there is enough light, the NE555 will turn on the LED.
After that, the LED will stay on even in darkness until it gets turned off with the switch.
The photodiode and the 22 kOhm resistor work together as a voltage divider.
In darkness, the voltage is high (9V). It drops with increasing brightness.
If the voltage drops below 3V, the NE555 will turn on its exit.
You can switch the two resistors in the circuit to change the sensivity.
If there's a 10 kOhm voltage divider, the sensor will turn on with more brightness than at 22 kOhm.
Hinter dem 7. Türchen findest du einen Fototransistor. Das Bauteil sieht aus wie eine LED in einem klaren Gehäuse.
Von vorn sieht man jedoch die dunkle, lichtempfindliche Fläche.
Der längere Anschluss ist der Emitter.
Der kürzere Anschluss heißt Kollektor.
Bei Dunkelheit ist der Fototransistor ein Isolator. Aber je mehr Licht auf seine empfindliche Fläche fällt, desto mehr Strom leitet er.
Die Spannung am Trigger-Eingang sinkt dann. Bei genügender Helligkeit schaltet der NE555 die LED ein.
Sie bleibt danach auch bei Dunkelheit an, bis sie mit dem Taster gelöscht wird.
Der Fototransistor arbeitet zusammen mit dem Widerstand von 22 kOhm als Spannungsteiler.
Bei Dunkelheit ist die Spannung hoch (9 V), mit steigender Helligkeit sinkt sie. Sobald die Spannung unter 3 V fällt,
schaltet der NE555 seinen Ausgang ein. Du kannst die beiden Widerstände in der Schaltung tauschen,
um die Empfindlichkeit zu ändern. Mit 10 kOhm im Spannungsteiler schaltet der Sensor erst bei größerer Helligkeit ein.
7 Light sensor
Behind the 7th door, there is a photodiode. It looks like a LED in a clear shell.
But at the front, you can see a dark, light-sensitive surface.
The longer port is called the emittor.
The shorter port is called the collector.
In darkness, the photodiode is an isolator. But it gets more conductive the more light falls onto its photosensitive surface.
If that happens, the voltage at the Trigger-entry drops. If there is enough light, the NE555 will turn on the LED.
After that, the LED will stay on even in darkness until it gets turned off with the switch.
The photodiode and the 22 kOhm resistor work together as a voltage divider.
In darkness, the voltage is high (9V). It drops with increasing brightness.
If the voltage drops below 3V, the NE555 will turn on its exit.
You can switch the two resistors in the circuit to change the sensivity.
If there's a 10 kOhm voltage divider, the sensor will turn on with more brightness than at 22 kOhm.